iPhone 11 Pro Motherboard Repair in Al Khobar

iPhone 11 Pro Motherboard Repair in Al Khobar fixes a phone that won't power on or keeps restarting. We check the board free and find the faulty part under a microscope. Then we replace that one small part, not the whole board, and keep your data wherever we can.

An iPhone 11 Pro not turning on is the sign we hear about most. The screen stays black, even after hours on a good charger. Some phones show the logo, go dark, then show the logo again in a loop.

Other board faults are quieter. The phone may get warm while switched off, lose its signal, or charge only on some days. Face ID can also stop working after a fall or a splash.

It's better not to wait. A short on the board keeps heating the parts near it, and any water inside keeps spreading rust. Leaving it can turn a small repair into one that can't be done.

Not every dead phone has a board fault, so we test the battery, screen and port first. When it is the board, we look closer. The iPhone 11 Pro motherboard has two layers stacked together, and often only one tiny part has failed.

How Kabayan Center Repairs an iPhone 11 Pro Motherboard

These are the board faults we fix on the 11 Pro.

• No power, even on a good charger
• A logo that loops again and again
• Restarts every few minutes during normal use
• No signal or no Wi-Fi after a fall
• A phone that runs warm while it's off
• Faults that begin days after a splash or a drop in water

Here is how an iPhone 11 Pro motherboard repair works, step by step.

1. We check the phone free and test it with a known good battery, screen and cable.
2. We connect a power meter that shows how much current the board pulls.
3. We explain what we found, and you decide before any work starts.
4. We open the screen from the front, disconnect the battery and lift out the board.
5. We trace the fault under a microscope, using the meter and gentle heat.
6. We replace the failed part with a hot-air tool and a fine soldering tip.
7. We rebuild the phone and test power, charging, signal, Face ID and the cameras.

Got another phone or a laptop with a board fault? Our motherboard repair service covers those too. Customers come to our shop on King Fahd Road from Dammam and Dhahran as well.

Why an iPhone 11 Pro Board Fails: 3 Real Cases

Dropped in the toilet, then dried with a hair dryer

A common case starts in the bathroom. A shop owner dropped the phone into the toilet and grabbed it out at once. Then came a long blast from a hot hair dryer to dry it.

The phone worked for a day, then went black for good. The owner had searched for iPhone Motherboard Repair in Al Khobar that evening. "I did everything right, I dried it straight away," the owner said.

A hair dryer only dries the outside, and its heat can push water deeper inside. The water left on the board slowly turns to rust under the chips.

We found green crust around the power parts and near the top of the board. So we did a water damage repair, cleaning the board in a special bath. Then the iPhone 11 Pro motherboard repair replaced two rusted parts, and the phone powered on.

Calls, photos and charging all worked again. Face ID, though, stayed unavailable, because water had reached the parts at the top. Those parts are paired to the board, so they can't simply be swapped.

The owner now unlocks with a passcode and has every file back. We suggested bringing a wet phone in switched off, with no heat at all.

Restarts after a battery swap elsewhere

A customer came to us after a battery was fitted at a small stall. From that day on, the phone restarted every few minutes. "It's worse than before the new battery," they said.

They had looked up mobile repair in Al Khobar, thinking the new battery was bad. The battery was part of it, but not all of it. Prying a battery out the wrong way can tear the tiny socket it plugs into.

Under the microscope, the battery socket on the board had two lifted pins. The battery was also a weak, poorly made copy. Both together made the power cut in and out.

We rebuilt the socket on the board with fresh solder and checked it with the power meter. Then we did a phone battery replacement with a good battery.

The restarts stopped completely during a long bench test. We ran it with the camera and maps open to be sure. The customer got the phone back with all their chats and photos in place.

We explained the warning sign for next time. A phone that acts strangely right after a repair usually needs a second look quickly.

Dead after a long day in a parked car

This one starts in a car park in summer. A sales manager left the phone on the seat for an afternoon of meetings. Back in the car, the phone was too hot to hold and would not turn on.

Even after cooling, it stayed dead. A night on the charger showed nothing at all. Holding the buttons for a forced restart did nothing either.

Strong heat stresses the tiny parts that filter power on the board. When one fails, it can short and stop the whole phone from starting. The battery usually shuts the phone off to protect itself first, but not always.

Our power meter showed a short on one power line. Using gentle heat, we found a tiny filter part that was warmer than the rest. We finished the iPhone 11 Pro motherboard repair under the microscope, and the phone started on the first try.

Every photo and file was still there. The sales manager now keeps the phone in a bag in the footwell, out of the sun.

We also suggested a sunshade for the windscreen on long stops. It keeps the whole car cooler, not just the phone.

How to Keep Your iPhone 11 Pro Board Safe

• Switch a wet phone off and bring it in. Skip the rice and the hair dryer.
• Never leave the phone on a car seat or dashboard in summer.
• Choose a careful shop for any repair, because a torn socket can stop the whole phone.
• Use a case with thick corners to soften hard drops.
• Back up your photos and chats every week.
• Get phone repair in Al Khobar as soon as the phone restarts by itself or runs hot while off.

Related services

• Data recovery for photos and files on a phone that won't start
• Charging port repair for a cable that is loose or charges only at an angle