iPhone 6 Plus Motherboard Repair in Al Khobar

iPhone 6 Plus Motherboard Repair in Al Khobar fixes a phone that is dead, restarts or loses touch. We check the board free and find the failed chip under a microscope. Then we repair or replace that chip and save your data wherever we can.

An iPhone 6 Plus not turning on is one common sign, even on the charger. Others restart again and again, lose signal or show a grey flickering bar at the top. Touch then stops, and a new screen won't help, since the touch chips sit on the board.

It's better not to wait. A short can heat the parts around it, and moisture keeps spreading rust. A fault that is small today can spread to other parts of the board.

Not every dead phone has a board fault. A worn battery, a dirty port or a loose screen plug can look exactly the same. We test those first, so you never pay for board work you don't need.

When the iPhone 6 Plus motherboard is at fault, we track down the exact chip. The big, thin body can flex in a pocket, and that flexing cracks tiny joints under chips. We repair those joints or fit a new chip.

How Kabayan Center Repairs an iPhone 6 Plus Motherboard

We fix these board faults on this phone.

• No power, even on a good charger
• A grey flickering bar at the top, with touch that stops working
• Restarting by itself, or stuck on the logo
• No service, or a weak signal after a bend
• A phone that gets warm while switched off
• Faults after water, steam or a drip

Here is how an iPhone 6 Plus motherboard repair works with us.

1. We check the phone free and test the battery, port and screen first.
2. We connect a power meter that shows how the board draws power.
3. We tell you what we found, and you decide before any work starts.
4. We open the phone from the front, disconnect the battery and take out the board.
5. We find the faulty chip under a microscope, using the meter and gentle heat.
6. We repair the joints or fit a new chip with a hot-air tool and fine solder.
7. We rebuild the phone, test touch, power, signal and Touch ID, then let you check it.

Need board work on another phone or a laptop? Our motherboard repair service covers other devices too. Customers come to our King Fahd Road shop from Dammam and Dhahran.

Why an iPhone 6 Plus Board Fails: 3 Real Cases

The grey bar that a new screen didn't fix

A customer came to us after paying for a new screen somewhere else. The grey flickering bar was still there, and touch still froze. "I changed the screen, and nothing changed," they said.

The customer, an office manager, had searched for iPhone Motherboard Repair in Al Khobar after reading about the bar. On this model, the board can flex a little in a pocket. Over time, that breaks the tiny joints under the two touch chips.

We tested the screen on our bench, and it was fine. Under the microscope, the touch chips had lost contact with the board. We lifted them, cleaned the pads and fitted them back with fresh solder.

The grey bar was gone, and touch worked across the whole screen. We added a thin support to make the area stiffer.

During the final test, the battery health showed a low reading. So we also did a phone battery replacement before closing it.

The phone now works smoothly with the screen fitted elsewhere. The manager now keeps it in a bag, not a tight pocket.

We explained the fault so the next repair starts in the right place.

Dripping water from a split AC unit

This one starts in a bedroom. A cook charged the phone every night on a shelf under the indoor AC unit. One summer, the unit began to drip from a blocked drain.

Each night, a few drops landed on the phone. It worked for a while, then it restarted, and then it stayed dark. The cook had looked up mobile repair in Al Khobar after a morning alarm failed.

AC water looks clean, but it carries dust and minerals. On a board, those minerals start rust, especially while the phone is charging.

We opened it and found green crust near the power parts and around the battery plug. We did a water damage repair, cleaning the board in a special bath.

Then we did the iPhone 6 Plus motherboard repair, replacing two rusted power parts. The phone turned on, charged and kept every file.

Never charge a phone that has been dripped on, even a little. The cook moved the charger to a dry table and called someone to fix the AC drain.

The phone has worked well since, with no restarts. The morning alarm rings on time again.

Bent under weights in a gym bag

We often see this with phones packed into crowded bags. A fitness trainer carried the phone under heavy ankle weights in a gym bag. The big phone came out with a gentle curve along its length.

Soon it showed no service most of the day. "Calls drop, and the signal bars are always empty," the trainer said. The phone held client photos that were not backed up.

Board work always carries a small risk on a bent phone. So before any work, we copied the photos through our data recovery service.

The bend had cracked joints under a chip near the signal parts. We did the iPhone 6 Plus motherboard repair with fresh solder, and the phone found its signal again. Calls stayed connected in our test.

But the frame stayed slightly curved, and signal was weaker than normal in some rooms. The trainer chose to keep using it, knowing it may drop calls inside large buildings.

So the signal is back, though not as strong as a straight phone. The trainer now keeps the phone in a separate pocket of the bag. The weights go in the bottom, well away from it.

How to Keep Your iPhone 6 Plus Board Safe

• Keep the phone out of tight back pockets and heavy bags.
• Charge it on a dry table, away from AC units, sinks and windows.
• Switch it off after any drip or spill and bring it in quickly.
• Use a good charger and an undamaged cable.
• Back up your photos every month.
• Get phone repair in Al Khobar as soon as a grey bar appears or touch freezes.

Related services

• Charging port repair for a cable that is loose or only charges at an angle