iPhone 6S Plus Motherboard Repair in Al Khobar

iPhone 6S Plus Motherboard Repair in Al Khobar brings a dead or faulty board back to life. We check it free and find the failed part under a microscope. We replace that part instead of the whole board, and we save your data wherever we can.

An iPhone 6S Plus not turning on is the most common sign. The screen stays black, even after hours on the charger, and nothing vibrates. Others lose signal, freeze on the logo or restart in the middle of a call.

Many owners try a reset, a new charger or a full night of charging first. If nothing changes, the fault is most likely on the board itself. That's the point where we can help.

It's better not to wait. A short on the board can heat and damage the healthy parts around it. Water or sweat left inside keeps eating the board, so the repair gets harder each day.

Not every dead phone has a board fault, though. A worn battery or a loose screen cable can look just the same, so we test those first. When the iPhone 6S Plus motherboard is at fault, it's usually one small part, and we replace just that.

How Kabayan Center Repairs an iPhone 6S Plus Motherboard

These are the board faults we fix on this phone.

• No power, even on the charger
• Stuck on the logo, or restarting again and again
• No signal, or a network search that never ends
• A phone that heats up while switched off
• No charging, even with a good port and battery
• Faults that appear after water or a hard drop

Here is how we repair the board, step by step:

1. We check the phone free and test the battery, screen and port to rule them out.
2. We measure how much power the board pulls with a power meter.
3. We tell you what we found, and you decide before any work starts.
4. We open the screen, unplug the battery and take the board out of the frame.
5. We find the failed part under a microscope, using the meter and a cold spray.
6. We do the iPhone 6S Plus motherboard repair with a hot-air tool and a fine soldering tip.
7. We rebuild the phone and test power, signal, charging and cameras before you check it.

Have a different phone or a laptop? Our motherboard repair service covers other devices too. Customers come to our shop on King Fahd Road from Dammam and Dhahran as well.

Why an iPhone 6S Plus Board Fails: 3 Real Cases

A screwdriver slipped during a home battery change

A customer came to us after trying to change the battery at home. A flat screwdriver slipped while prying out the old battery. There was a small spark, and the phone never turned on again.

"There was a little pop, then nothing," they said. They had searched for iPhone Motherboard Repair in Al Khobar that night. A metal tool can bridge the battery's power to the board in a flash.

The old battery was dented where the tool had pressed. A dented battery is a fire risk. So we did a phone battery replacement and disposed of the old one safely.

The iPhone 6S Plus motherboard repair was not over, since the board drew no power. Under the microscope, a tiny filter part beside the battery connector was burnt black. We replaced it with a fine soldering tip.

The phone powered on with all its data. Touch, charging and signal all tested normally. The owner was very relieved to see the photos again.

Never pry a phone battery out with metal tools. The stretch strips under it are made to pull out, and plastic tools do the rest. Opening a phone at home is riskier than it looks.

Dropped from a treadmill at the gym

We often see this after a hard fall. A gym trainer kept the phone on a treadmill shelf while running. It bounced off the belt and hit the floor hard.

The screen survived without a crack. But the phone showed no network, and every call failed. "Wi-Fi works, but no signal at all," the trainer said.

The trainer had looked up mobile repair in Al Khobar, sure it was a SIM problem. We tried a new SIM and checked the settings first. The fault stayed, so it needed an iPhone 6S Plus motherboard repair.

A hard knock can crack the tiny solder joints under a chip. Under the microscope, we found a cracked joint near the signal chip. We cleaned the area and joined it again with fresh solder.

The network came back, and test calls went through clearly. We left the phone running a long test, and the signal held the whole time. Messages arrived in a rush once it connected.

The trainer now leaves the phone in a locker while running, or in a zipped pocket. The treadmill shelf is for water bottles only. That small habit protects more than the screen.

Dropped in a toilet, then dried with a hair dryer

This one starts at a wedding hall. The phone slipped from a shirt pocket into a toilet. The owner pulled it out fast, then dried it with a hair dryer for a long time.

Hot air feels like the right thing, but it pushes water deeper. It also heats the small parts on the board. The phone worked for a few days, then went black.

We opened it and found rust spreading under several chips. We did a water damage repair, cleaning the board in a special bath. But some fine lines under one chip were already eaten through.

The board could not be brought back for daily use. We could still reach the storage, and that mattered most. Through our data recovery service, we saved the photos, contacts and videos.

So the phone was gone, but the wedding photos were not. The owner moved everything to a new phone soon after. Every video from that night was safe.

A wet phone needs a check right away. Switch it off, and skip both the hair dryer and the rice. Those first minutes matter more than anything else.

How to Keep Your iPhone 6S Plus Board Safe

• Never open the phone with metal tools.
• Switch a wet phone off and bring it in, without heat or rice.
• Use a zipped pocket or a locker at the gym.
• Use a good charger and cable, not an unbranded one.
• Back up your photos and chats every week.
• Get phone repair in Al Khobar as soon as the phone loses signal or restarts by itself.

Related services

• Charging port repair for a cable that is loose or only charges at an angle