iPhone X Motherboard Repair in Al Khobar

iPhone X Motherboard Repair in Al Khobar fixes a phone that won't start or keeps looping on the logo. We check the board free and trace the fault under a microscope. Then we replace the failed part, not the whole board, and save your data wherever we can.

An iPhone X not turning on is the most common reason people bring us this phone. The screen stays black, and even a forced restart or the charger makes no difference. Others show the logo again and again, or lose their signal for good.

It's better not to wait. A short keeps heating the parts around it, so the damage spreads to more of the board. Water left inside keeps eating the copper lines, day after day.

Not every dead phone has a board fault. A flat battery or a loose screen cable can look just the same. We test those first, so you only pay for board work you really need.

The iPhone X motherboard is built in two layers pressed together, like a sandwich. It packs a lot into a small space, but the joints between the layers can crack. Often one joint or one tiny part has failed, and we repair only that.

How Kabayan Center Repairs an iPhone X Motherboard

We fix these board faults on the iPhone X.

• No power, even on the charger
• Looping on the logo, or restarting again and again
• No signal, or Wi-Fi that won't switch on
• No charging with a good port and battery
• Heat while the phone is switched off
• Faults that start after heat, a drop or water

These are the real steps of an iPhone X motherboard repair.

1. We check the phone free and test the battery, screen and port to rule them out.
2. We connect a power meter that shows how much current the board draws.
3. We tell you what we found, and you decide before any work starts.
4. We open the screen, disconnect the battery and lift the board out of the frame.
5. We separate the two layers when needed and find the fault under a microscope.
6. We replace the failed part or rejoin the layers with fresh solder.
7. We rebuild the phone and test power, charging, signal, Face ID and cameras.

Board trouble on another phone or a laptop? Our motherboard repair service covers other devices too. Our shop is on King Fahd Road, and customers come from Dammam and Dhahran as well.

Why an iPhone X Board Fails: 3 Real Cases

Left in a parked car at midday

This one starts in a car park in the middle of summer. A sales rep left the phone on the seat during a long meeting. When the rep came back, the phone was too hot to touch and switched off.

Once it cooled, it showed the logo and then restarted, over and over. "It just won't finish starting," the rep said. They had searched for iPhone Motherboard Repair in Al Khobar that same afternoon.

Strong heat makes the two board layers expand, then shrink again as they cool. Doing that many times can crack the tiny joints between them. Under the microscope, we found a weak area along one edge.

In this iPhone X motherboard repair, we separated the layers, cleaned them and joined them again with fresh solder. The phone then started normally and passed a long test.

The battery, though, had swollen a little from the heat. A swollen battery is not safe to keep using. So we fitted a new one with a phone battery replacement.

The rep now takes the phone into every meeting. In summer, a car can turn into an oven within minutes.

A trip through the washing machine

We often see this with work trousers. A cleaner's phone stayed in a pocket and went through a full wash. It came out silent, with water behind the screen.

The owner had looked up mobile repair in Al Khobar and brought it in the next morning. Soap and hot water had reached every part of the phone. The spin cycle had pushed the water into places a splash never reaches.

"I tried to switch it on straight away," the cleaner admitted. Many people do, but power on a wet board speeds up the damage.

Inside, we found soap crust and rust on both layers of the board. We did a water damage repair, cleaning each layer in a special bath. But several lines inside the board had already been eaten through.

The iPhone X motherboard repair could not bring the board back to safe, daily use. The memory chip, though, still worked. We saved the photos and contacts through our data recovery service.

The owner moved everything onto a new phone that same week. So the phone was lost, but the photos of the family were not.

A quick check of the pockets before every wash would have kept the phone dry.

No signal after a rushed repair elsewhere

A customer came to us after a screen change at another shop. The new screen looked fine, but the phone showed no signal from that day on. "They said it's a network problem," the customer told us.

A new SIM card and a reset had not helped. That made us look at the board, not the settings. A network fault would not start on the exact day of a repair.

When a screen is opened in a rush, a metal tool can slip onto the board. On a crowded iPhone X motherboard, one slip can knock a tiny part off. Those parts are smaller than a grain of rice.

Under the microscope, a tiny part near the signal area was missing. Its empty pads were scratched where the tool had hit them. We fitted a new part in its place with a fine soldering tip.

After the iPhone X motherboard repair, full signal came back on the first test call. Calls, data and Wi-Fi all worked again.

The customer now asks to see the tools before any repair. We suggested always backing up the phone before it goes in for a fix, anywhere.

How to Keep Your iPhone X Board Safe

• Never leave the phone in a parked car in summer, not even for a short stop.
• Check every pocket before the wash.
• Never charge a phone that got wet, and skip the rice. Bring it in quickly instead.
• Use a good charger and cable, and stop using any plug that gets hot.
• Back up your photos and chats every week, and before any repair.
• Get phone repair in Al Khobar as soon as the phone loops on the logo.

Related services

• Charging port repair for a plug that is loose or only charges at one angle